Continuous warning after upgrade to 1.8.x

aurora protocol http://www.curtronics.com/Solar/
lacchini
Posts: 15
Joined: Sun Jun 16, 2019 3:40 pm

Continuous warning after upgrade to 1.8.x

Post by lacchini » Sun Jun 16, 2019 4:02 pm

hi all,
maybe it's a coincidence but since I updated to version 1.8 I get warnings all the time, even 100 times a day, at this point I don't understand if there is really a problem.
Can anyone figure out what the problem is? below are some examples of warnings:
# 123Solar Alarms Warnings digest 16/06/2019 16:44:05 20190616-16:44:56 300.994141 2.817989 848.198120 298.776764 2.824434 843.875122 242.166931 6.794881 1633.959839 50.021008 96.565552 50.941654 48.278805 OK
123Solar Alarms Warnings digest 16/06/2019 16:34:00 20190616-16:34:50 302.976044 2.886465 874.529724 299.973755 2.901771 870.455261 242.897751 6.989336 1687.623535 49.999001 96.712784 51.446720 48.544983 OK
# 123Solar Alarms Warnings digest 16/06/2019 16:24:02 20190616-16:24:53 298.423553 3.025834 902.980042 295.578247 3.037918 897.942383 240.833603 7.273959 1743.221191 50.016006 96.796021 52.188007 48.990112 OK

thank you all

Leo

jeanmarc
Posts: 1866
Joined: Thu Aug 29, 2013 7:16 am

Re: Continuous warning after upgrade to 1.8.x

Post by jeanmarc » Sun Jun 16, 2019 4:10 pm

Hi Leo,
What odd messages :shifty: Do you use aurora protocol or someting like socat ?
Stop 123s and what return aurora -a 2 -A /dev/ttyUSB0 (adapt it) ?

lacchini
Posts: 15
Joined: Sun Jun 16, 2019 3:40 pm

Re: Continuous warning after upgrade to 1.8.x

Post by lacchini » Sun Jun 16, 2019 8:05 pm

aurora protocol of course
with version previous i had no problem
now it is late becouse the sun went down
actually :
root@MONITOR:~# aurora -a 2 -A /dev/ttyUSB-Aurora

Alarm 1: No Alarm
Alarm 2: No Alarm
Alarm 3: No Alarm
Alarm 4: No Alarm

tomorrow i copy the output when inverter will start

jeanmarc
Posts: 1866
Joined: Thu Aug 29, 2013 7:16 am

Re: Continuous warning after upgrade to 1.8.x

Post by jeanmarc » Sun Jun 16, 2019 9:12 pm

did you have debug enabled, any notification filters ?
When it happens, what files are in data/invt1/msgqueue/ ?

lacchini
Posts: 15
Joined: Sun Jun 16, 2019 3:40 pm

Re: Continuous warning after upgrade to 1.8.x

Post by lacchini » Mon Jun 17, 2019 6:45 am

now:
root@MONITOR:~# aurora -a 2 -A /dev/ttyUSB-Aurora

Alarm 1: No Alarm
Alarm 2: No Alarm
Alarm 3: No Alarm
Alarm 4: No Alarm

@jean
debug no
comunication option : -a 2 -c -T -Y6 -l5 -d0
digest message : 0
notification filter : W011,W001,E011
check inverter alarm/message/lost : all yes

thank's all !!!

jeanmarc
Posts: 1866
Joined: Thu Aug 29, 2013 7:16 am

Re: Continuous warning after upgrade to 1.8.x

Post by jeanmarc » Mon Jun 17, 2019 8:04 am

That's ok to me..
What files are in data/invt1/msgqueue/ ?

lacchini
Posts: 15
Joined: Sun Jun 16, 2019 3:40 pm

Re: Continuous warning after upgrade to 1.8.x

Post by lacchini » Mon Jun 17, 2019 6:49 pm

nothing, the folder is empy

i set digest to 60 minutes to reduce the push to mobile

jeanmarc
Posts: 1866
Joined: Thu Aug 29, 2013 7:16 am

Re: Continuous warning after upgrade to 1.8.x

Post by jeanmarc » Mon Jun 17, 2019 7:15 pm

So you get this on rpinotify | pushover | mail ?
You definitely should have files in msgqueue before it happens.
Do you run latest version ?

lacchini
Posts: 15
Joined: Sun Jun 16, 2019 3:40 pm

Re: Continuous warning after upgrade to 1.8.x

Post by lacchini » Tue Jun 18, 2019 10:35 am

rpinotify via telegram
yes the latest version
until version 0.7.x i the system didn't send any warning / digest
i receive the digest since upgraded to 0.8.x

i'am afraid my plants have some problem but on the inverter display i see no error, all is ok

in the digest latest row report "OK" message

but i don't understand the number of the message :(

this is the latest digest :
123Solar Alarms Warnings digest 18/06/2019 10:39:01 20190618-10:39:52 309.353455 2.830878 875.742065 308.548920 2.826850 872.221619 236.688782 7.178512 1690.040894 49.980007 96.686272 48.626980 46.127396 OK18/06/2019 10:34:04 20190618-10:34:55 311.296112 2.772070 862.934509 310.491577 2.768042 859.453613 238.912445 7.009047 1665.868042 49.982006 96.718506 48.380375 45.839748 OK18/06/2019...

jeanmarc
Posts: 1866
Joined: Thu Aug 29, 2013 7:16 am

Re: Continuous warning after upgrade to 1.8.x

Post by jeanmarc » Tue Jun 18, 2019 2:02 pm

There is no worries with those returns, they are just data not reals alarms.
I've reviewed the code, i don't see where that come from.
Please update to 1.8.3.2, also i really need to see files in msgqueue/ to see why it happen.

Post Reply

Who is online

Users browsing this forum: No registered users and 2 guests